Scarp and Channels in a Crater in Terra Cimmeria
NASA/JPL-Caltech/UArizona
Scarp and Channels in a Crater in Terra Cimmeria
PSP_001936_1370  Science Theme: Glacial/Periglacial Processes
This image shows a crater in Terra Cimmeria, approximately 10 kilometers (6 miles) in diameter. The roughly concentric ridges and troughs in this crater's floor are known as "concentric crater fill," and probably result from compression caused by viscous flow of a thick mixture of rocks, soils, and ice inward from the crater's walls.

This and other examples of concentric crater fill occur at high latitudes, where theoretical calculations indicate that ice may exist under the surface, mixed with rocks and soil.

This subimage shows a small portion of the crater's north-looking wall (downhill is up, illumination is from the left). In the lower part of the subimage a relatively harder, rocky layer protrudes from the crater's wall; some blocks broke up from it and fell down the slope. Loose soils accumulated behind these blocks (uphill), forming what looks like bright-colored tails. The crater's floor, in the upper part of the subimage, is covered here by elongated dunes. A channel 7 to 20 meters (7.5 to 22 yards) wide cuts deeply into the crater's wall; it is unclear if this channel was carved by a fluid or by landslides.

The channel is cut by a younger scarp (shown with yellow arrows pointing downhill) which approximately separates the crater's wall from its floor. This cliff can be followed for more than 3 kilometers (2 miles) along the Southern part of the crater's floor. Elsewhere in this image channels similar to the one shown here cut through (and, therefore, are younger than) the scarp, extending inside the crater's floor. This scarp may have been produced by settling of the crater's floor, maybe due to flow of ice, soil, and rocks towards the center of the crater, and/or to sublimation of underground ice.



Written by: Sara Martinez-Alonso  (25 April 2007)
 
Acquisition date
25 December 2006

Local Mars time
15:47

Latitude (centered)
-42.723°

Longitude (East)
158.529°

Spacecraft altitude
251.4 km (156.2 miles)

Original image scale range
from 25.2 cm/pixel (with 1 x 1 binning) to 50.3 cm/pixel (with 2 x 2 binning)

Map projected scale
25 cm/pixel and North is up

Map projection
Equirectangular

Emission angle
2.3°

Phase angle
72.3°

Solar incidence angle
74°, with the Sun about 16° above the horizon

Solar longitude
155.9°, Northern Summer

For non-map projected images
North azimuth:  97°
Sub-solar azimuth:  36.8°
JPEG
Black and white
map projected  non-map

IRB color
map projected  non-map

Merged IRB
map projected

Merged RGB
map projected

RGB color
non-map projected

JP2
Black and white
map-projected   (850MB)

IRB color
map-projected   (464MB)

JP2 EXTRAS
Black and white
map-projected  (355MB)
non-map           (542MB)

IRB color
map projected  (133MB)
non-map           (419MB)

Merged IRB
map projected  (204MB)

Merged RGB
map-projected  (207MB)

RGB color
non map           (403MB)
ADDITIONAL INFORMATION
B&W label
Color label
Merged IRB label
Merged RGB label
EDR products
HiView

NB
IRB: infrared-red-blue
RGB: red-green-blue
About color products (PDF)

Black & white is 5 km across; enhanced color about 1 km
For scale, use JPEG/JP2 black & white map-projected images

USAGE POLICY
All of the images produced by HiRISE and accessible on this site are within the public domain: there are no restrictions on their usage by anyone in the public, including news or science organizations. We do ask for a credit line where possible:
NASA/JPL-Caltech/UArizona

POSTSCRIPT
NASA’s Jet Propulsion Laboratory, a division of the California Institute of Technology in Pasadena, Calif., manages the Mars Reconnaissance Orbiter for NASA’s Science Mission Directorate, Washington. The HiRISE camera was built by Ball Aerospace and Technology Corporation and is operated by the University of Arizona.